What is an ink service module?

The Ink Service Module (ISM) is where the ink goes to when the print cartridges are being serviced. For a typical customer, they should not have to replace the ISM during the life of the printer.

In the same way How do you clean an ink service module?

After removing the module, soak it in a hot soapy water solution (I used Dawn dishwashing soap) for about an hour in a small disposable plastic container. Rinse out the module and soak it again in a fresh solution of soap and water. Keep repeating these steps until the module rinses clean.

Subsequently, How do I reset my HP Officejet 100 Mobile Printer?
Step one: Reset the printer

1. With the printer turned on, disconnect the power cord from the rear of the printer.
2. Unplug the power cord from the wall outlet.
3. Wait at least 15 seconds.
4. Plug the power cord back into the wall outlet.
5. Reconnect the power cord to the printer.
6. Turn the printer on.

How do I check ink levels on my HP Officejet 100 printer?

Follow these steps to check the ink levels on your product, and then replace low or empty cartridges according to the results.

1. Load plain white paper into the tray.
2. On the product control panel, press and hold the Cancel button ( ) for three seconds. The self-test report prints.

What is the pairing code for HP Officejet 100 Mobile printer?

The product ships with a predefined PIN code that is set to six zeroes (000000). Any Bluetooth device within range can print to the product. The product does not require a PIN code. Any Bluetooth device within range can print to the product.

How do I connect my HP Officejet 100 Mobile printer?

HP Officejet 100 Mobile Printers (L411a and L411b) – Printing a Bluetooth Configuration Page

1. Load plain white paper into the tray.
2. On the product control panel, press and hold the Bluetooth button ( ) for three seconds. The Bluetooth configuration page prints.

How do I reset my HP printer phone?

Remove the battery from the product, if it is installed. Disconnect the power cord from the rear of the product, if it is connected. Unplug the power cord from the electrical outlet, if it is plugged in. Wait at least 30 seconds.

What is the pairing code for HP Officejet 100 Mobile Printer?

The product ships with a predefined PIN code that is set to six zeroes (000000). Any Bluetooth device within range can print to the product. The product does not require a PIN code. Any Bluetooth device within range can print to the product.

How do I connect my HP Officejet 100 to Bluetooth?

Set the Bluetooth security settings

1. Click the HP Utility icon in the Dock. …
2. Under Printers, click your product, if more than one printer is listed.
3. Click Bluetooth Settings.
4. To require users to type a six-digit PIN code before sending a print job from their Bluetooth device, follow these steps:

How do I connect my phone to my HP printer?

Add a printer using Wi-Fi Direct: On your printer, make sure Wi-Fi Direct is turned on. On your mobile device, tap All printers > Add printer, and then tap HP Print Service or HP Inc. Tap Directly to the Printer, select the name of your printer with DIRECT in the name, and then tap OK.

How do I make my printer discoverable?

Here’s how:

1. Open Windows search by pressing Windows Key + Q.
2. Type in “printer.”
3. Select Printers & Scanners.
4. Hit Add a printer or scanner. Source: Windows Central.
5. Choose The printer that I want isn’t listed.
6. Select Add a Bluetooth, wireless or network discoverable printer.
7. Choose the connected printer.

How do I reset my HP Bluetooth?

Resetting Bluetooth security settings

1. Press and hold the Power button ( ).
2. While you hold down the Power button, press the Cancel button ( ) four times, and then press the Resume button ( ) six times.
3. Release the Power button.

How do I reset my HP Officejet 150?

HP Officejet 150 Mobile All-in-One Printer – Resetting the…

1. Step 1: Remove the battery. The reset might not work correctly if the battery is installed. …
2. Step 2: Reset the printer. Disconnect, and then reconnect the power cord to reset the printer. …
3. Step 3: Reinstall the battery.

How do I reset my HP Officejet 150 all in one?

Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the rear of the printer.

How do I connect my HP 100 to WIFI?

On the printer touch the setup button, (wrench) then select network setup menu, select wireless menu, select wireless direct and turn it on. On the computer, in the bottom right corner click on the wireless icon and select the printer from the list to connect to.

How do I reset my Bluetooth printer?

With the printer turned off, find the reset button located on the back of the printer, and then use a pen to press and hold down the button. While holding down the reset button, turn on the printer. Continue holding the reset button for 10 seconds after turning on the printer, and then release the reset button.

How do I setup my printer to print from my phone?

Start your mobile application and tap the Settings icon. (Mobile Cable Label Tool users must also tap [Printer Settings] – [Printer].) Select the printer listed under [Wi-Fi Printer]. You can now print from your device wirelessly.

How do I print from my phone to my printer?

Most smartphones use Android, these will be the phones that use the Google Play Store.

1. Open the file you’d like to print.
2. Tap the menu button. It looks like three stacked dots.
3. Tap “Print”.
4. Tap the drop-down arrow. It’s located near the top of your screen.
5. Tap the printer you’d like to print from.
6. Tap the print button.

Why can’t my Android phone find my printer?

Open Google Cloud Print, tap on “Settings”, then on “Printing.” If your printer is on the same WiFi network as your Android device, it should show up in the list and add itself. Then you can print from some apps by tapping the “…” that usually indicates more options, to find and tap on the Print option.

Why cant my computer find my wireless printer?

Run the printer troubleshooter. If your computer can’t detect your wireless printer, you can also try to fix the problem by running the built-in printer troubleshooter. Go to Settings > Update & Security > Troubleshooter >run the printer troubleshooter.

Why isn’t Bluetooth working on my HP?

Other steps to try: Uninstall the Bluetooth drivers from device manager and restart the computer and check if it works again. Right-Click on start button> click device manager> expand Network adapters>then select the network drivers that are listed and right-click on it and uninstall the drivers.

Why won’t my Bluetooth device connect to my laptop?

If your Bluetooth devices won’t connect, it’s likely because the devices are out of range, or aren’t in pairing mode. If you’re having persistent Bluetooth connection problems, try resetting your devices, or having your phone or tablet “forget” the connection.

Which type of connections do HP Officejet 150 Mobile All in One printer supports?

In addition to USB connectivity, the Officejet 150 Mobile can print from a Windows Mobile device and a BlackBerry. Additionally, you can print from other mobile devices using Bluetooth connectivity. The Officejet 150 can print from and scan to an SD card, MMC card, or USB drive.

Don’t forget to share this post with your friends !